Ashville, AL

Performed complimentary clean and check inspection on HVAC system. Inspected all system components, verified proper operation, cleaned accessible areas, and confirmed unit functionality. System found to be operating within normal parameters with no immediate service needs identified.

Completed Clean & Check service on HVAC system that was approximately 5 years old or less. Performed standard maintenance inspection and system evaluation as part of a new customer setup through referral.

Completed drive-by assessment of residential HVAC system approximately 5 years old or less. Established new Club Care Advantage Contract (CCAC) for ongoing maintenance and service coverage based on referral from existing customer family member.

Conducted drive-by assessment of property to evaluate potential service needs and determine if assistance could be provided. Performed visual inspection of accessible areas and systems to identify any immediate concerns or issues requiring attention.

Responded to no cooling complaint on split air conditioning system. Diagnosed and resolved cooling issue on 3-ton unit operating under warranty coverage. System restored to proper operation and verified performance upon completion of Service Agreement Visit.

Responded to callback for air conditioning system not maintaining temperature. Performed diagnostic evaluation of cooling system to identify cause of inadequate performance and addressed issues preventing unit from keeping up with cooling demand.

Responded to a callback for an HVAC system not cooling properly. Performed diagnostic inspection and troubleshooting to identify the cause of inadequate cooling performance. Completed necessary repairs to restore proper system operation and cooling functionality.

Responded to warranty service call for HVAC system tripping circuit breaker. Breaker had been previously replaced but unit continued to trip after approximately one hour of operation. Diagnosed electrical issue causing intermittent overcurrent condition and performed necessary troubleshooting to identify root cause of breaker trips.

Responded to callback for HVAC unit that would not shut off. Diagnosed and resolved thermostat wiring issue causing continuous operation. Verified proper system cycling and confirmed unit now responds correctly to temperature settings.

Responded to service call for frozen HVAC unit. Diagnosed cause of freeze-up condition, which typically results from restricted airflow due to dirty air filter, blocked return vents, low refrigerant charge, or malfunctioning blower motor. Thawed evaporator coil, identified and corrected underlying issue to restore proper system operation and prevent recurrence.

Completed encapsulation carpet cleaning process on commercial carpeting. Applied encapsulation cleaning solution using rotary machine with bonnet pads to lift and crystallize soil particles, followed by grooming to ensure even distribution and proper drying.

Completed initial Protection Plan Visit for HVAC system. Performed comprehensive inspection of heating and cooling equipment, including filter check, thermostat calibration, electrical connection verification, and condensate drain assessment. System operating within normal parameters with no immediate service needs identified.

Completed initial turnover and commissioning of indoor air quality system. Performed comprehensive testing and verification of all IAQ components and equipment. System operational and ready for service.

Completed encapsulation of ductwork system to seal and protect against air leakage and contamination. Applied specialized encapsulation material to all accessible duct surfaces, ensuring proper coverage and adhesion throughout the system. Verified integrity of encapsulation upon completion to maintain improved air quality and system efficiency.

Completed encapsulation of ductwork system to seal and protect against air leakage, moisture infiltration, and energy loss. Applied specialized encapsulation material to all accessible duct surfaces, ensuring proper adhesion and coverage throughout the system. Verified encapsulation integrity and confirmed improved system efficiency upon completion.

Completed first service agreement visit for air conditioning system. Performed comprehensive system inspection, checked refrigerant levels, cleaned condenser coils, replaced air filter, and verified proper operation of all components. System is operating within manufacturer specifications and ready for the cooling season.

Completed initial service call for new customer to perform equipment turnover. No air conditioning system was present at the property requiring equipment setup and installation preparation. Documented site conditions and equipment requirements for future installation work.

Completed encapsulation of ductwork system to seal and protect against air leakage, moisture infiltration, and contaminant exposure. Applied specialized encapsulation coating to all accessible ductwork surfaces, ensuring proper adhesion and coverage throughout the system. Verified integrity of encapsulation upon completion to meet industry standards for improved energy efficiency and indoor air quality.

Completed routine preventive maintenance service agreement visit on HVAC system. Performed comprehensive inspection of heating and cooling equipment, changed air filters, checked refrigerant levels, tested thermostat operation, cleaned condensate drain lines, and verified all safety controls were functioning properly. System found to be operating within manufacturer specifications with no immediate repairs required.

Provided comprehensive estimate for moisture control solutions focusing on encapsulation and ductwork sealing. Assessment included evaluation of crawlspace or affected areas requiring vapor barrier installation and ductwork treatment to prevent condensation and moisture intrusion. Recommended encapsulation system and ductwork modifications to address humidity issues and improve overall environmental conditions.

Performed comprehensive Clean & Check maintenance on air conditioning system with history of previous operational issues. Conducted thorough inspection of all components, cleaned condenser and evaporator coils, checked refrigerant levels, tested electrical connections, and verified proper system operation. All maintenance tasks completed successfully to ensure optimal cooling performance and system reliability.